The special feature of Aluma-Hyde II (and the reason for its development) is its increased resistance to bore cleaners, solvents and other cleaning chemicals, even trichloroethylene. Today’s family of fast, aggressive bore cleaners really do a terrific job getting dirty gun bores sparkling clean, but they can wreak particular havoc with any other finish they contact. After full cure, Aluma-Hyde II proved solvent-proof to all but the most aggressive, copper-removing bore solvents. Aluma-Hyde II is formulated with a hard-curing epoxy base that contains additional, high-density pigment for a durable finish that sticks to all properly prepared aluminum and alloy surfaces, steel and plastics - it’s great on synthetic stocks. Aluma-Hyde II is available in a variety of colors to help the gunsmith match the vast number of applications found in the average gunshop. Aluma-Hyde II dries to the touch in only minutes and reaches full cure in about a week. Absolutely no primer coat is required for a tough, durable, abrasion-resistant, rustproof finish that blends beautifully and compliments all gun finishing applications.
Each can of Aluma-Hyde II is now supplied with a Clean Out Nozzle, required to be used before each use of the paint to prevent clogs in the Nozzle and Pickup Tube. Aluma-Hyde Clean Out Nozzles allow nearly unrestricted pressure to flow through the pickup tube and nozzle to clear out any semi-hardened paint that may be in the pickup tube. Once clear, replace with the original spray nozzle and start your project. When used correctly, this will ensure a smooth, sputter free paint application free of clumps or inconsistencies.
Additional Clean Out Nozzles can be purchased as singles, 430107431, or in a 12-pack, 084179004. Clean Out Nozzles are not intended for finish spraying.
SPECS: 12 oz. (340 g) aerosol can.
INSTRUCTIONS:
PREP THE SURFACE: NO priming required on clean, bare metal or anodized surfaces. Surface should be dry and free of oil, wax, dirt, loose paint, and any other contaminants. Painted surfaces should be washed with a cleaner degreaser. If cleaning parts with abrasive blasting, make sure blasting media is oil- and silicone-free. Test a small area for color compatibility and adhesion.
• Unpainted aluminum: Abrasive blast to achieve desired surface look/texture.
• Unpainted steel: Remove rust by sanding or abrasive blasting.
• Fiberglass: Sand lightly, then wash with soap and water or clean with a quality cleaner degreaser.
• Wood: Seal or fill surface. ALUMA-HYDE II can be applied over polyurethane and varnish finishes but not over linseed oil or tung oil finishes.
PREP CAN: For best results, use between 70° F and 90° F (not below 65° F). Shake can vigorously until the ball inside rattle; then shake for 2 minutes more to achieve correct color and texture.
INITIAL CLEARING SPRAY: Before spraying work surface, point can in safe direction and depress valve. Press until spray is consistent in color and consistency. The cleanout nozzle can be used in this step for previously used, or even new cans. The cleanout nozzle is used to ensure any residue or buildup is easily ejected from the can. Simply pull the standard nozzle upwards off the can and press the cleanout nozzle down in its place (be careful to point can in safe direction when pressing downwards, as can may discharge spray).
Cleanout Nozzles are included with each can of Aluma-Hyde purchased from Brownells and is available separately. Search item number 430107431.
SPRAY IT ON: Hold can approximately 12” away from the work surface and fully depress valve on top to start the spray. Shake can periodically during application process.
LET IT CURE: This is a critical step in getting a truly tough, long-lasting finish! If a second coat is needed, it should be applied within 30 minutes. After 30 minutes, Aluma-Hyde II must be allowed to cure 10-14 days before recoating.
• Dries to a light touch in approximately 10-15 minutes. Wait 24 hours or more before extensive handling.
• Complete cure time caries depending on film thickness, temperature, and humidity
• Cure time can be reduced by circulating warm air (90°F max.) or placing part in direct sunlight.
• Aluma-Hyde II can be “speed cured” by baking the part for 3.5 hours at 195°F. Allow part to cool before applying another coat.